MARBLE CLEANING IN DUBAI
Remove the build-up before you remove the finish.
For marble that looks dirty, greasy, streaked or congested with maintenance residue while the stone underneath is still fundamentally sound. We identify what is sitting on the surface first, then use controlled cleaning chemistry, agitation and extraction suited to the stone instead of treating every mark as a polishing problem.
IS CLEANING THE RIGHT SERVICE?
Deep cleaning removes contamination and maintenance build-up. It does not mechanically recreate worn gloss, grind lippage or rebuild broken stone. Separating those conditions prevents unnecessary refinishing.
CLEANING IS USUALLY THE RIGHT ROUTE WHEN
POLISHING OR RESTORATION SHOULD BE ASSESSED WHEN
WHAT MARBLE CLEANING TARGETS
The aim is to remove what is sitting on or in the upper pores of the surface without unnecessarily cutting or changing a finish that may still be serviceable.
Entrances and circulation areas collect fine dust, grit and tracked contamination that gradually darkens the surface.
Target: lift embedded soil before deciding whether finish correction is also needed.Kitchen-adjacent areas, commercial spaces or repeatedly treated floors can develop a film that smears instead of cleaning evenly.
Target: break down compatible residue without aggressive abrasion.Repeated mopping with unsuitable product strength can leave a cloudy or streaked appearance that mimics loss of polish.
Target: remove residue and reassess the true finish underneath.Grout lines, skirting edges and corners often hold soil after the open floor has been routinely cleaned.
Target: restore a cleaner visual line around the stone layout.Spills or absorbed contamination may create darker or discoloured areas that need isolated treatment rather than whole-floor refinishing.
Target: test the stain response before escalating to a heavier process.Light construction dust, protective-product residue or handover film can remain after fit-out even where the marble itself is new.
Target: clean the installed surface without confusing residue with stone damage.WHAT HAPPENS ON SITE
We adjust chemistry, dwell time, agitation and extraction to the condition in front of us. Stain treatment and joint work are isolated where needed instead of over-treating the entire floor.
We inspect traffic lanes, stains, joint lines, previous coatings or cleaners and test whether the problem is removable contamination or actual finish wear.
Loose abrasive particles are removed first so cleaning does not drag grit across the marble. Sensitive joinery, metals or nearby finishes are protected where required.
The cleaning solution is selected for the stone and contamination, then allowed enough contact time to loosen residue without treating dwell time as a fixed recipe.
Mechanical or manual agitation is used according to the area, with attention to corners, joints and perimeter lines before dirty solution is removed from the surface.
After the marble is clean, remaining stains, etching, scratches or finish wear are easier to identify. We then advise whether any polishing, stain treatment or restoration is still justified.
MARBLE CLEANING RATES
Cleaning cost depends on contamination level, access, measured area, joint condition and whether isolated stain or edge work is required. We do not hide restoration work inside a generic cleaning rate.
| Service scope | From | Unit | What it covers |
|---|---|---|---|
| Marble Deep Cleaning | AED 12 | /m² | General deep cleaning for soil, residue and maintenance build-up |
| Spot Stain Treatment | AED 30 | /spot | Localized treatment for a small stain after compatibility assessment |
| Regrouting & Joint Touch-Up | AED 18 | /m² | Joint cleaning and grout refresh where this forms part of the agreed scope |
| Silicone / Edge Refinish | AED 21 | /lm | Wet-area or perimeter edge clean-up and compatible silicone refinishing |
AED 12 /m²
General deep cleaning for soil, residue and maintenance build-upAED 30 /spot
Localized treatment for a small stain after compatibility assessmentAED 18 /m²
Joint cleaning and grout refresh where this forms part of the agreed scopeAED 21 /lm
Wet-area or perimeter edge clean-up and compatible silicone refinishingIndicative starting rates only. Final pricing depends on stone type, contamination, staining, measured area, joint condition, access and project requirements. Polishing, grinding, crack repair and material replacement are excluded unless specifically quoted.
WHAT A GOOD CLEAN SHOULD LEAVE BEHIND
The target is a residue-free, evenly cleaned surface that makes the true finish condition visible. We do not promise artificial gloss from cleaning chemistry when the marble actually needs refinishing.
WHERE WE DEEP-CLEAN MARBLE
Open floors, bathrooms, entrance zones and counters do not collect the same contamination, so the method and edge work are adjusted to the application.
MATERIAL SUITABILITY
Acid-sensitive stones and previously sealed surfaces cannot be treated like porcelain. Where material or coating history is uncertain, a controlled test area is the safer starting point.
CLEANING, POLISHING OR RESTORATION?
The fastest route is not always the heaviest route. Cleaning targets contamination; polishing targets finish wear; restoration targets deeper damage and repair.
DIRT / RESIDUE
FINISH WEAR
DAMAGE / REPAIR
MARBLE CLEANING FAQ
The important distinction is whether the problem is contamination on the surface or wear within the finish itself.
Our indicative rate for marble deep cleaning starts from AED 12/m². Localized stain treatment, joint work and edge refinishing have separate starting rates because they require different time and materials. The final quotation depends on measured area, contamination level, access and whether polishing or repair is also needed.
Cleaning can reveal the original finish when residue, grease or detergent film is making the marble look cloudy. If the surface is already clean but the gloss layer is worn, scratched or etched, polishing or honing is usually the more appropriate service.
Some stains respond to localized treatment, but the result depends on what caused the stain, how deeply it has penetrated and whether it reacted chemically with the stone. We prefer to test the affected area rather than promise that every stain can be removed by ordinary cleaning.
We do not treat natural marble like an acid-resistant tile. Marble is commonly acid-sensitive, so cleaner selection depends on the stone, contamination and finish. Strong acidic products can etch the surface and create a polishing problem while trying to solve a cleaning problem.
Yes, subject to access and working conditions. We plan area isolation, furniture movement, wet-work control and drying sequence according to the property so the cleaning scope is practical for an occupied environment.
If the marble looks better when residue is removed but the finish underneath still reflects consistently, cleaning may be enough. If a fully clean test area remains dull, etched or lightly scratched, the problem is in the finish and polishing should be assessed.
There is no useful fixed interval for every site. Foot traffic, entrance grit, cleaning products, wet-area use and maintenance quality all change the requirement. Professional deep cleaning is best scheduled around visible build-up and maintenance performance rather than an arbitrary calendar date.
NOT SURE IF THE MARBLE IS DIRTY OR ACTUALLY WORN?
Share the location, approximate area and the condition you are seeing. A clear surface photo often tells us whether cleaning is the right first route or whether the finish needs correction.